Post by MaggatSlayer on Jul 1, 2005 22:11:23 GMT -5
***Disclaimer***
Information may be debateable. Use at your own discretion. Always test before drilling a major part.
Angel:
Angel LED, LCD & IR3 detents ----- 1/8" BSP
angel feednecks ----- M21x0.75
ball detent threads ----- M10x1.00
Trigger screws ----- M4x10mm
Bottom body grub ----- M4x6mm
LPR and battery caps ----- M19x0.75 (roughly 0.748"-34 in English units)
Autococker:
valve retaining nut----- 5/8"-18 5/16" long hollow lock screw
valve locking nut (located on underside of body) ----- 5/16"-24 1/4" long set screw
cocking rod hex knob ----- 5/16" OD 10-32 stainless threaded hex standoff, 3/4" long
All (or most) newer hammer kits ----- 1/4"-28 x 1/2" setscrew, with the first approx. 3/16" turned down to just narrower than the 'Cocker body slot. (Itself 3/16".)
IVG 3/4-16
Bolt o-rings ----- 0.1" thick, 0.5" ID, 0.7" OD
front block bolts ----- 3/8-24 threads on '99 and earlier
9/16-24 threads on 2000 and later
detent ----- 3/8 -24
velocity adjuster ----- 3/4-16
3-way ----- 15/32"-32
ram - 6-32
cocker barrels ----- 15/16"-20, Oversize GH-7
Autococker LPR ----- 1/8" NPT
Phantoms:
Barrel threads ----14 TPI Acme threads with a major dia. of 0.860"
nylock in bolt ---- 10-32 , ~0.147" long
Impulse:
feed necks ----- 32tpi, around .807" major dia
valve lock screw ----- 7/16"-20
frame screws ----- 1/4"-20, 1" long
front cap -----1"-16
impulse VA bolt ----- 3/8"-27
Viking:
End-caps ----- 3/4"-20
Feed-neck ----- 15/16"-20, Oversize GH-7
Barrel ----- 15/16"-20, Oversize GH-7
Pre-'05 Bushmaster:
Tray - Body Screws: (4) 6-32 x 1" (Socket Head Cap)
Valve Retaining Set Screw: 3/8-24 x 1/4" (socket set screw, fine thread)
Grip Frame - Tray Screws: (2) 8-32 x 3/8" (Allen Head is 4-40)(Button head)
Grip - Grip Frame Screws: (4) 6/32 x 1/4" (Button Head)
Trigger Set Screws: (3) 8-32 x 1/4" (Set Screw)
Valve Set Screw: (1) 1/8NPT plug
Manifold - Body Screws: (4) 4-40 x 3/8" (Button Head)
2k3 Eye Cover Screws: (2) 6-32 x 5/8 b (b= Button Head)
New Style Ball Detents (O-ring) Screws: (1) 6/32 x 1/4" (Button Head)
Bottomline: (2) 10/32 various length
Switch/Battery Cover screws:3-48 x 3/16
2k3 Eye cover screws: 6-32 x 5/8 Button head
Valve set screw: 1/8NPT plug...same as the plugs that plug up the holes for gauges if u dont use one
Shocker
Feedneck : 32 TPI
Spyder
Esprit-
Ball detent screw - M4 x 6
Feedneck screws - M4 x 8
Front block/VA - M5 x 14 + washer
Sight rail screw - M4 x 12 + washer
On/Off switch screw - M2 x 6
Coil set screws - 1/8"
Trigger Frame screws - M5 x 12
Grip Panel screws - M3 x 10 (ESP and 45 frames)
Pre- '05 Imagine
Feedneck screw- M4 x 6
Ball Detent screw- M4 x 8
Front Block/VA- M5 x 12.5 + washer
Trigger Frame screw- M5 x 12 + washer
Sight Rail screw- M4 x 12 + washer
Bottom Line CA screw- 5/32" x 7/8"
On/Off Switch screws- M2 x 6
Coil set screw- 1/8"
'05 Imagine-
Front Block/VA screw- M5 x 14 + wahser
Trigger Frame screw- M5 x 12
Bottom Line/CA screws- 5/32" x 7/8"
On/Off switch screw- M2 x 6
Xtra-
Beavertail screw- M4 x 6 with washer
Frame to Drop forward- 5/32" x 5/8" screw with washer
ASA to drop forward- 5/32" x 7/8" screw with washer
Grip panel screw- M3 x 10
VA screw- M5 x 14 screw with washer
Frame to body- M5 x 12 screw with washer
Detent Cover- M4 x 6 screw with washer
vertical feed neck- M4 x 6 screw with washer
Spyder Barrel threads are Metric 1.5
BKO
Ram screws: (2) 10-32 x 1/2" (Button Head)
ASA Block screw: (2) 10/32 x 3/4" (Socket Head Cap)
Valve Retaining Set Screw: 3/8-24 x 1/4" (socket set screw, fine thread)
Tray - Body Screws: (4) 6-32 x 7/8" (Socket Head Cap)
Grip Frame - Tray Screws: (2) 8-32 x 3/8" (Allen Head is 4-40)(Button head)
Grip - Grip Frame Screws: (4) 6/32 x 1/4" (Button Head)
Trigger Set Screws: (3) 8-32 x 1/4" (Set Screw)
Valve Set Screw: (1) 1/8NPT plug
New Style Ball Detents (O-ring) Screws: (1) 6/32 x 1/4" (Button Head)
Bottomline: (2) 10/32 various length
Standard:
normal gauge/macro ------ 1/8" npt tap
grip frame/bottom line screws ------ 10/32
asa ------ 1/2 NPS tap
Have Blue's Tap Chart
Complete technical info containing tap sizes for most markers
Click to order taps and dies
For the above link, I recommend reading the Patents section. It explains alot and some new stuff not even on the market.
Information may be debateable. Use at your own discretion. Always test before drilling a major part.
Angel:
Angel LED, LCD & IR3 detents ----- 1/8" BSP
angel feednecks ----- M21x0.75
ball detent threads ----- M10x1.00
Trigger screws ----- M4x10mm
Bottom body grub ----- M4x6mm
LPR and battery caps ----- M19x0.75 (roughly 0.748"-34 in English units)
Autococker:
valve retaining nut----- 5/8"-18 5/16" long hollow lock screw
valve locking nut (located on underside of body) ----- 5/16"-24 1/4" long set screw
cocking rod hex knob ----- 5/16" OD 10-32 stainless threaded hex standoff, 3/4" long
All (or most) newer hammer kits ----- 1/4"-28 x 1/2" setscrew, with the first approx. 3/16" turned down to just narrower than the 'Cocker body slot. (Itself 3/16".)
IVG 3/4-16
Bolt o-rings ----- 0.1" thick, 0.5" ID, 0.7" OD
front block bolts ----- 3/8-24 threads on '99 and earlier
9/16-24 threads on 2000 and later
detent ----- 3/8 -24
velocity adjuster ----- 3/4-16
3-way ----- 15/32"-32
ram - 6-32
cocker barrels ----- 15/16"-20, Oversize GH-7
Autococker LPR ----- 1/8" NPT
Phantoms:
Barrel threads ----14 TPI Acme threads with a major dia. of 0.860"
nylock in bolt ---- 10-32 , ~0.147" long
Impulse:
feed necks ----- 32tpi, around .807" major dia
valve lock screw ----- 7/16"-20
frame screws ----- 1/4"-20, 1" long
front cap -----1"-16
impulse VA bolt ----- 3/8"-27
Viking:
End-caps ----- 3/4"-20
Feed-neck ----- 15/16"-20, Oversize GH-7
Barrel ----- 15/16"-20, Oversize GH-7
Pre-'05 Bushmaster:
Tray - Body Screws: (4) 6-32 x 1" (Socket Head Cap)
Valve Retaining Set Screw: 3/8-24 x 1/4" (socket set screw, fine thread)
Grip Frame - Tray Screws: (2) 8-32 x 3/8" (Allen Head is 4-40)(Button head)
Grip - Grip Frame Screws: (4) 6/32 x 1/4" (Button Head)
Trigger Set Screws: (3) 8-32 x 1/4" (Set Screw)
Valve Set Screw: (1) 1/8NPT plug
Manifold - Body Screws: (4) 4-40 x 3/8" (Button Head)
2k3 Eye Cover Screws: (2) 6-32 x 5/8 b (b= Button Head)
New Style Ball Detents (O-ring) Screws: (1) 6/32 x 1/4" (Button Head)
Bottomline: (2) 10/32 various length
Switch/Battery Cover screws:3-48 x 3/16
2k3 Eye cover screws: 6-32 x 5/8 Button head
Valve set screw: 1/8NPT plug...same as the plugs that plug up the holes for gauges if u dont use one
Shocker
Feedneck : 32 TPI
Spyder
Esprit-
Ball detent screw - M4 x 6
Feedneck screws - M4 x 8
Front block/VA - M5 x 14 + washer
Sight rail screw - M4 x 12 + washer
On/Off switch screw - M2 x 6
Coil set screws - 1/8"
Trigger Frame screws - M5 x 12
Grip Panel screws - M3 x 10 (ESP and 45 frames)
Pre- '05 Imagine
Feedneck screw- M4 x 6
Ball Detent screw- M4 x 8
Front Block/VA- M5 x 12.5 + washer
Trigger Frame screw- M5 x 12 + washer
Sight Rail screw- M4 x 12 + washer
Bottom Line CA screw- 5/32" x 7/8"
On/Off Switch screws- M2 x 6
Coil set screw- 1/8"
'05 Imagine-
Front Block/VA screw- M5 x 14 + wahser
Trigger Frame screw- M5 x 12
Bottom Line/CA screws- 5/32" x 7/8"
On/Off switch screw- M2 x 6
Xtra-
Beavertail screw- M4 x 6 with washer
Frame to Drop forward- 5/32" x 5/8" screw with washer
ASA to drop forward- 5/32" x 7/8" screw with washer
Grip panel screw- M3 x 10
VA screw- M5 x 14 screw with washer
Frame to body- M5 x 12 screw with washer
Detent Cover- M4 x 6 screw with washer
vertical feed neck- M4 x 6 screw with washer
Spyder Barrel threads are Metric 1.5
BKO
Ram screws: (2) 10-32 x 1/2" (Button Head)
ASA Block screw: (2) 10/32 x 3/4" (Socket Head Cap)
Valve Retaining Set Screw: 3/8-24 x 1/4" (socket set screw, fine thread)
Tray - Body Screws: (4) 6-32 x 7/8" (Socket Head Cap)
Grip Frame - Tray Screws: (2) 8-32 x 3/8" (Allen Head is 4-40)(Button head)
Grip - Grip Frame Screws: (4) 6/32 x 1/4" (Button Head)
Trigger Set Screws: (3) 8-32 x 1/4" (Set Screw)
Valve Set Screw: (1) 1/8NPT plug
New Style Ball Detents (O-ring) Screws: (1) 6/32 x 1/4" (Button Head)
Bottomline: (2) 10/32 various length
Standard:
normal gauge/macro ------ 1/8" npt tap
grip frame/bottom line screws ------ 10/32
asa ------ 1/2 NPS tap
Have Blue's Tap Chart
Complete technical info containing tap sizes for most markers
Click to order taps and dies
For the above link, I recommend reading the Patents section. It explains alot and some new stuff not even on the market.